Universal 12V Car Battery Switch Wireless Remote Control Disconnect Cut Off Isolator Master Add our listing to Watchlist Or Add to Cart , you will get more discount The BPM-12 electric paralysis protector is an intelligent electronic device installed on the battery. Monitor the electric quantity and charge and discharge state in real time while working. When the battery is about to run out of electricity, the battery will be disconnected in time in order to retain the minimum electricity needed for the next start-up, and to protect the battery from excessive discharge. The equipment is connected between the electric bottom and the negative number of equipment by this method. It is often used for battery protection, RV double battery isolation protection, motorcycle electric protection, computer room spare battery protection and so on. Working voltage: 12V Standby current 1.5mA Through current: 120a Instantaneous current: 1200A Suitable for vehicle type: vehicles with displacement 4.0 Remote control:320ft/1Pc Product characteristics 1.Non-contact switch control to completely eliminate dust and water vapor entry 2.Remote control 3. OLED screen display voltage, power, on-off,intuitively visible, visual settings. 4. LED working status display 5. Power saving design, standby orbital mode as low as 400 microamperes, an average working current of 1.5 Ma, to provide 180 days of parking protection 6. 16 square pure copper flame retardant specification, supporting super large start-up current. 7. Pure thickening manual switch, easy to install, and provide convenient and fast manual turn-on mode. 8. 120A self-locking on-off controller, supporting short-term 1200A start-up current, standby zero power consumption. 9.Special circuit design, support input and output installation at will, support positive and negative pole installation at will. 10. Full sealing + sealing + EVA sealing process, providing IP68 grade (highest grade) protection standard. 11.Military grade devices, built-in hardware watchdog, to ensure stable operation. 12. Disaster safety design, even in the case of the maximum failure of the chip and its surrounding circuits, the self-locking characteristics of the on-off controller can still maintain its normal turn-on and ensure the safety of driving. Method of use 1. The equipment boot display screen is turned on, showing the product model and version, and entering the main interface after 2 seconds; 2. The main interface has four thin display content 84%: remaining battery capacity 12.63v: real-time bottom voltage 50%: disconnect power settings When the real-time power is lower than the disconnected power and the well lasts longer than the set disconnect time, the equipment will cut off the power supply Sm: devices work in enhanced security mode (no display indicates regular protection mode) Onon and off status of devices On- connected. 0ff- Disconnect, Time to zero and disconnect immediately. 3. Key OFF/-: When the screen goes out in standby state, click wake up screen display In the bright screen state, click will perform the shutdown action, disconnect the battery from the electrical equipment: in setting mode, click to perform digital subtraction operation, see the setup wizard for details. 4. Key ON/+: When the screen goes out in standby state, click on the wake-up screen to display When the screen state, click will perform the opening action, connect the battery to power the device; in setting mode, click to perform digital plus operation, see the setup wizard. 5. Remote Controller: OFF- disconnects battery from electrical equipment ON- turns on battery to power equipment 6. LED: red light flashes to disconnect and green light flashes to turn on. The red light flashes once in 1 second, indicating manual or remote disconnection. The red light flashes once in 2 seconds, indicating that the equipment is automatically disconnected and that the remaining battery power is sufficient. The red light flashes once in 5 seconds, indicating that the power has been exhausted and must be charged immediately. The green light flashes once a second, indicating that the bottom capacity is sufficient. green light flash quickly, indicating that the remaining power is below the set value, disconnect countdown, Special reminder: A: When OFF is set up in safe running mode, there is no limit to the new opening, and disconnection is performed unconditionally whenever an instruction is received. B. The safe operation mode is set to ON, at a real-time voltage Above 13.2v(The system thinks that the engine is running and the generator is generating normally). The equipment will not accurately respond to any disconnect instructions to ensure driving safety with maximum procedures (see the section on setting up wizard safety town switches for details). Packing list